Fire Alarm Estimating: How to Take Off and Price a Fire Alarm System

Fire alarm work looks small on the drawings, a few symbols on each floor, but it carries real risk for electrical contractors. Device counts, cable routes, programming, testing and inspections all add up, and the code and the authority having jurisdiction (AHJ) decide what is acceptable. Fire alarm estimating is about counting every device, measuring every circuit and pricing the work that never appears as a symbol.

This guide covers what to include in a fire alarm takeoff, how system type affects labor, and the low-voltage items that often get bundled into the same scope.

Before you start: scope and design responsibility

  • Who designs the system? Some projects include a full fire alarm design. Others are design-build, where the fire alarm contractor provides shop drawings, calculations and permit submittals. Design-build adds engineering and submittal time to the estimate.
  • Who furnishes and who installs? On many jobs the fire alarm vendor furnishes the panel and devices and the electrical contractor installs boxes, conduit and cable. Confirm the split before you price.
  • Occupancy and codes: the building type, size and use drive what the system must include. NFPA 72 and the local fire code, plus any AHJ requirements, set the rules.
  • New or existing: renovations may require tying into an existing panel, keeping the system live during work and fire watch.

Fire alarm estimating: what to take off

A complete fire alarm takeoff counts each device type separately, because each has a different material and labor cost:

  • Control equipment: fire alarm control panel (FACP), power supplies (NAC extenders), batteries, annunciators and any network or radio communicators
  • Initiating devices: smoke detectors, heat detectors, duct detectors, manual pull stations, beam detectors
  • Notification appliances: horns, strobes, horn-strobes, speakers and speaker-strobes, ceiling and wall mount
  • Modules: monitor modules for sprinkler flow and tamper switches, control and relay modules for elevator recall, HVAC shutdown, door holders and dampers
  • Boxes, conduit and cable for every circuit, measured along the real route

Fire alarm takeoff tips

  • Use the device legend on the current set; symbols vary by designer.
  • Count the riser diagram as well as the floor plans. It often shows modules and connections that plans do not.
  • Check the mechanical drawings for duct detectors and the plumbing or fire protection drawings for flow and tamper switches.
  • Check the elevator and door hardware schedules for recall, shunt trip and door holder connections.

Addressable vs conventional fire alarm systems

In a conventional system, devices are wired in zones, so the panel knows which zone is in alarm but not the exact device. In an addressable system, each device has its own address, so the panel identifies the exact point and location. Addressable systems are standard on most commercial work today. They usually take more labor per device because of addressing, programming and point-by-point testing, so price the programming and testing time, not just the installation.

Wire, conduit and installation labor

Follow the specifications for cable type and raceway. Some projects allow fire alarm cable without conduit in accessible spaces; others require conduit throughout. Signaling line circuits (SLC) and notification appliance circuits (NAC) are usually different cable types. Speaker circuits may need separate cable as well. Measure each circuit along its route, add drops to each device and include boxes, supports and firestopping. Ceiling height, building occupancy and work hours all affect labor.

Low voltage estimating in the same package

Fire alarm is often bid together with other low-voltage systems. Confirm which of these are in your scope, and take them off separately:

  • Data and telecom cabling, outlets, racks and backboards
  • Security cameras, access control and intrusion detection
  • Nurse call (healthcare) and intercom systems
  • Audio-visual rough-in and sound systems
  • Empty conduit and pull boxes for systems installed by others

Common mistakes in fire alarm estimates

  1. Leaving out duct detectors and modules shown only on other trades’ drawings.
  2. Pricing installation but not programming, testing and the final AHJ inspection.
  3. Missing engineering, shop drawings, battery and voltage-drop calculations on design-build work.
  4. Ignoring permit fees, monitoring setup and fire watch on renovation projects.
  5. Using a cost per square foot instead of counting the actual devices.

Fire alarm estimating FAQ

How much does a fire alarm system cost per square foot?

Square-foot figures are only useful for very early budgets. The real cost depends on the occupancy, system type, device count, cable and conduit requirements, ceiling heights, location and labor rates. For a bid, price the actual devices and circuits from the drawings.

Is fire alarm part of the electrical estimate?

Often, yes. Fire alarm is commonly part of the electrical scope (CSI Division 28), but some projects carve it out to a specialty contractor. Check the scope of work and bid form.

What should a fire alarm takeoff include?

The control panel and power supplies, every initiating device, notification appliance and module by type, plus boxes, conduit, cable, programming, testing and inspections.

Get a fire alarm and electrical takeoff

MEP Estimation Services prepares fire alarm and low-voltage takeoffs as part of our electrical estimating services for contractors across the United States. We also cover plumbing and mechanical work, and full MEP estimating services. For a refresher on device counts, see our electrical takeoff checklist. Need quantities only? See our MEP quantity takeoff services. You get color-coded marked-up drawings and an Excel file, usually within 24-48 hours.

Send your plans for a free quote.